EMT Practice Test

1. Question Content...

---

Question1: When configuring SLB load balancing parameters, which statement is true about the
"sticky" setting?

Question2: Which first character starts an AppRule comment?

Question3: An enterprise has two Juniper DX appliances front ending two clusters with two Servers behind each. IP addresses for this configuration are shown below:DX1 ether 0:
10.10.1.5DX2 ether 0:
10.10.1.6Cluster VIP: 10.10.1.10Cluster VIP: 10.10.1.11In the Juniper DX's ActiveN Blades section of the ActiveN Configuration page, which two IP addresses should be configured as ActiveN blades? (Choose two.)

Question4: Which two functions require the use of the CLI? (Choose two.)

Question5: Which configuration parameters are needed to configure this SLB group on the JuniperDX?

Question6: Which Juniper DX service uses 3G Cache?

Question7: An enterprise uses multiple servers to manage its web site. The servers are not identical and some are more powerful than others. Which Cluster algorithm provides optimal server load balancing?

Question8: A financial institution is placing the Juniper DX in front of an existing server which uses SSL. Due to security concerns they want to maintain the SSL encryption all the way from the client to the server. Which three statements are true? (Choose three).

Question9: Which DX process is used to provide nonweb SSL termination?

Question10: Which CLI command is used to set a Privileged Exec password of mypassword?

Question11: What is the default cache size?

Question12: What must you do before you enable Unified Failover?

Question13: An administrator chooses the default Cluster load balancing algorithm. Which statement is true?

Question14: How do you disable a server from Juniper DX Cluster without terminating active client requests?

Question15: Which two types of nodes are included in an MPLS explicit route?

Question16: In which two situations should you run the command sync group? (Choose two.)

Question17: Which three statistics are available when viewing content types of the cluster statistics page? (Choose three.)

Question18: In a production environment, which two steps are required to enable SSL between the client and the Juniper DX? (Choose two.)

Question19: What are two uses of the AS Path attribute?

Question20: Which configuration command establishes an EBGP session to a peer in AS 300?

Question21: How many different Clusters can use same AppRule file?

Question22: Which two ways does the DX appliance accelerate web servers? (Choose two.)

Question23: An enterprise has a web application running both HTTP and HTTPS. How many Clusters must be created?

Question24: What is the purpose of the OSPF hello packet?

Question25: Which file should be sent to JTAC for all DX appliance support cases?

Question26: Which DX services does Unified Failover support?

Question27: Which CLI command display the metric associated with each advertised route?

Question28: When configuring SMTP Health Check parameters for SLB, which two statements are true? (Choose two.)

Question29: When implementing BGP confederations, which configuration command establishes the globally unique ASnumber used with external peers outside your network?

Question30: You would like to configure a channelized OC3 interface with the following properties:
Slot 4 Port 0
Path Channel 3
Virtual Tributary Group 4
Virtual Tributary 1 times lots 112Which set of configuration commands accomplishes this goal?

Question31: Which three TCP protocols are supported in a Forwarder? (Choose three.)

Question32: When using a Redirector on the DX appliance, which HTTP response code is sent back to the client when they make a request to a redirected URL?

Question33: Which message is used to transport routing information between BGP peers?

Question34: An enterprise uses a Webtiered application that provides NTLM end user authentication.
What is the required Cluster option?

Question35: Which CLI command shows real time compression statistics through a Juniper DXcluster?

Question36: How are AppRules executed?

Question37: Which two troubleshooting commands require the use of the CLI? (Choose two.)

Question38: Which configuration command configures ISIS to support MPLS Traffic Engineering?

Question39: Which configuration command is used to make the ERX Edge Router an NTP server?

Question40: Which three transport methods are used to transfer a TCP dump? (Choose three.)

Question41: When configuring OSPF on the ERX, what is the default auto cost reference band width value?

Question42: Which CLI command is used to capture network traces?

Question43: An administrator wants to ensure that all copyright notices in web content have the correct date. Which AppRule type will be used?

Question44: During OSPF adjacency formation, what state is a router in when it is sending LSA header information to its neighbor?

Question45: Which three statements about Label Switched Paths (LSPs) are true?

Question46: Which is the default SSL protocol used for the Listen Side on a Forwarder?

Question47: What are three characteristics of RIPv2?

Question48: Which packet is sent in response to a BGP Open packet?

Question49: Which service uses AppRules?

Question50: What do you need to upgrade the DXOS?

Question51: You are configuring the DX appliance for the first time using the console. Which two configuration values can be set using the first time configuration screen? (Choose two.)

Question52: In the Juniper DX Unified Failover configuration, the VMAC is active on Which device(s)?

Question53: Which command displays the result of a loopback test you executed on a CT3 line module in slot 5, port 0,t1 number 4?

Question54: An administrator wants to verify a target server's availability for an application. Which two statements are correct? (Choose two.)